You Must Know the Problem Before You Can Fix It
Plumbing is a modern marvel of convenience that nosotros often take for granted — until something goes wrong and the shine functioning of our households comes to a screeching halt. This is especially true when you lot're dealing with toilet problems, which can certainly feel like bug that you'll desire to get resolved as apace as possible. Fortunately, many common toilet issues are small issues you can fix yourself without calling in a plumber (and paying emergency fees). If you come across 1 of these everyday toilet bug, attempt the respective quick fix to return your bathroom to skillful working order.
The Ghost Flush
No, the bathroom isn't haunted — but when "ghost flushing" happens, the toilet sounds like it's refilling the same way it does after it'due south been flushed…without having been flushed. You might hear this refilling audio as often as every few minutes or every few hours throughout the twenty-four hours, and it typically ways that water is leaking from the tank into the bowl. This tin can happen when the flapper — the plug that rests against the bottom of the toilet tank and holds water in the tank until you flush — becomes muddied or damaged.
To decide whether the flapper is leaking, add a few drops of nutrient coloring to the toilet tank and wait one-half an hour. Cheque the toilet bowl; if the water in the bowl has the food coloring in it, you have an internal leak. Take a await at the flapper (it resembles a round disk or a rounded cap with a ball-shaped protrusion on the lesser that sits against a seal on the bottom of the tank) and wipe information technology off to remove any droppings. Clean up any sediment or debris around the flapper, on the seal below it and on the flush valve it's attached to.
If the ghost flushing continues after cleaning, or if the flapper or seal has visible damage like pitting or warping, supercede the flapper and seal. If, afterward replacing the flapper, the toilet is still ghost flushing, y'all may need to replace the flush valve that the flapper sits on.
This is perhaps the nearly routine problem you'll come across with your toilet, and it often happens if someone flushes too much newspaper. If you flush and notice that the bowl is bankroll up instead of emptying, a clog is a likely culprit. This blazon of clogging is especially mutual on older, depression-period toilets, which you can sometimes flush twice to successfully motion the paper through the pipes. If this doesn't work, information technology'south likely that the toilet itself is where the clog lies (and don't keep flushing — y'all don't desire an overflow on your hands).
Your start line of defense? A toilet flange plunger. This is a different type than the one-time-fashioned cup-style plunger y'all might be more familiar with. Instead, it has an upper cup with a flared, cylindrical flap extending from the bottom, a design characteristic that creates a improve seal against the pigsty in your toilet bowl — and therefore more suction to push button the clog through. To use this plunger on a clog, tip it slightly in the bowl to permit water flow into and fill its chamber; this creates force to push the clog. Keep the plunger handle vertical to prevent the seal from breaking, and plunge in an upwards-and-down motion quickly. If y'all notice information technology hard to plunge, try running the plunger under hot h2o to soften the rubber.
If the plunger doesn't unclog the toilet, you can utilise a tool called an auger (or snake) to push the clog through. This is a long, textured cable with a handle that you turn to spin the cable around and downwards through the toilet's drain pipage. To get to work on the clog, guide the cablevision down the drain hole in the toilet and start cranking the auger handle. If you experience resistance or the cable stops, you've reached the clog. Keep turning the handle to break up or hook the clog. Pull the auger out — it'll either have broken upwards the clog or pulled information technology out, too — and plunge the toilet a few times.
If the plunger and auger don't eliminate the clog, it's fourth dimension to telephone call in a plumber. The clog may be much farther down the line, and a plumber has heavier-duty equipment to handle the job.
The Stuck or Loose Handle
Your toilet'south handle should exist a footling loose right after y'all've flushed and the tank is filling back up. Only what if it's loose all the time — or doesn't want to budge? There are a few quick fixes to try here.
Start by taking the lid off of the toilet tank. Check out the area where the handle is attached to the tank; on the inside wall of the tank, you'll encounter a large nut, which holds the handle in place. Using an adaptable wrench, turn the nut to tighten it if the handle is loose, or loosen the nut if the handle is stuck.
If tightening the nut doesn't besides tighten upward the handle, you may need to adjust the lift chain. This attaches the lift arm — which is on the back of the handle inside the tank — to the flapper and brings the flapper up when you flush the toilet to let water into the basin. Sometimes this chain tin can stretch out, making the handle loose because there's not enough tension betwixt the elevator arm and the flapper. Unhook the chain from the lift arm and straighten it and then there's only about a half-inch of slack remaining. Then, reattach the chain to the elevator arm at the new link.
Source: https://www.questionsanswered.net/lifestyle/common-toilet-problems-and-quick-fixes?utm_content=params%3Ao%3D740012%26ad%3DdirN%26qo%3DserpIndex
0 Response to "You Must Know the Problem Before You Can Fix It"
Post a Comment